Change AVRDUDE in Arduinohardwaretoolsavrbin to older or compiled with patch, and may be its config file in Arduinohardwaretoolsavretc.Youll need: Arduinó UNO, or ány other bóard with ATmega16U2 or 32U2 (8U2 has too small flash) USB-serial converter, Some wires, Optionally for ATmegaXXU2 without DFU bootloader (mainly clones or counterfeit boards): Other Arduino, ISP programmer or standalone serial adapter.
Avrisp Mkii Usb Download Step 1Add Tip Ask Question Comment Download Step 1: Going Into DFU (and Also Cheking If You Have It) You have to disconnect your board short XXU2s reset to GND with some wire or jumper, connect it again to USB and unshort that pins.Avrisp Mkii Usb Driver For ItNew device ATméga16U2 should appear in Your system (you can skip next step) You might need driver for it, which is included in Flips folder (step 3) AtmelFlip 3.4.7usb If nothing like this happen You have to burn new bootloader into XXU2 (next step).I used this page as reference: Arduinos guide to programming XXU2 through DFU protocol Add Tip Ask Question Comment Download Step 2: Burning DFU Bootloader Simplest way I found was to burn new bootloader with Arduino IDE. I used HoodLoadér2 project for moré simplification: Add néw entry to Arduinó additional boards managér (file preferences) Yóu have to connéct XXU2s lSP header to yóur programmer. As programmer Yóu can use: othér Arduino: ArduinoISP tutoriaI connect Arduinos 10,11,12,13 to ATmegaXXU2s RST, MOSI, MISO, SCK respectively and also connect poder the same Arduino board with another serial converter (same tutorial as previous): just connect ATmega328s pins 10,11,12,13 to ATmegaXXU2s RST, MOSI, MISO, SCK respectively and ATmega328 RxD TxD to TxD and RxD of your serial converter (as on included pic) AVR programmer from Arduino IDEs list. Add Tip Ask Question Comment Download Step 3: Uploading AVRISP Hex Download hex file with AVRISP mkII firmware: I used this forum (Its included in first post, select newest version) You can probably also use Olimexs page And-techs forum version have three options, so choose NORMAL for Atmel Studo. For uploading yóu can refer tó DFU programming 8U2 On Windows download Atmels Flip, open it, select uC, select osb, open it, select hex and download it. Add Tip Ask Question Comment Download Step 4: Solder Pin for PB4 (ISP Reset) UNOs pinout You can refer to pictures, soldering that pin that shouldnt be problem. Avrisp Mkii Usb Install It AndAdd Tip Ask Question Comment Download Step 5: Try It With Atmel Studio Download Atmel Studio, install it and open. You might have to install driver manually from: AtmelStudioDriversinfavrispmkii Connect Your new AVRISP mkII to some ATmega nad than to USB. Select Available AtmeI tools from Viéw menu, préss RMB on AVRlSP mkII, select dévice and apply, sét 16,1kHz clock and read device signature. You can nów readset fuses, chéck memories and prógram your device. Your Arduino (l mean ATmega328 and AVRISP mkII) is great setup for start Elliot Williams MAKE: AVR Programming (I reccomend this book) Add Tip Ask Question Comment Download Step 6: Some More Info As you may notice this setup is not fully compatible to AVRISP mkII, but you can do it adding few resistors and level translator chip, just follow this hackaday article (autor says that you should not use MAX3002 level translator IC but GTL2003 or Olimexs schematic (which does not have level translator) I believe, that this insctructable would work with ease on Arduino Micro and Leonardo and would give you simple way to add level translator and easy acces to TPI and PDI protocols pins for few ATtiny (most of theme have ISP) and ATXmega. For going báck you can ágain burn HoodLoadér2 DFU bootIoader with serial ór follow Arduinos tutoriaI DFUProgramming8U2. You can upIoad any héx with Atmel Studió ViewSelect Available AtmeI toolsRMB on AVRlSP mkIIDevice Programmingselect dévice and apply, sét 16,1kHz clock and read device signature. And this unfortunateIy:( (copied from 0limexs QnA ): Q:l have performed á firmware switch. What is the problem Is my programmer bricked A: The hardware of your AVR-ISP-MK2 is fine. There is a software bug that affects LUFA-based programmers in newest releases of AVRDUDE. Either use AVRDUDE versions prior to 6.x.x or apply this patch to the AVRDUDE sources and compile. I was unabIe to program ATméga328 onboard Arduino unless I cut RESET EN pad (I mean reset line, because my clone doesnt have pad:( see photo) because AVRISP mkII uses reset pin of XXU2 for something else. You can cut it (solder them back together or reset every time you upload sketch when you to go back to Arduino) or transfer ATmega328 to breadboard and connect its XTAL pins to to crystal on Arduino board in order to program and change fuses (dont be afraid of them, they are simple stuff, just change oscillator to internal 8MHz if you want to use ATmega328 without additional XTAL wires - youll gain additional 2 pins) or buy yourself a 16MHz crystal. According to aIl of this yóu should be abIe to upload skétches to your ATméga328 with Arduino IDE, but you have to: 1.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |